I2C on the Gumstix

From GumstixDocsWiki

Jump to: navigation, search

A tutorial to get I2C working on the Gumstix for use with things like the Robostix.

Contents

General

Note: the I2C section of the gumstix motherboard I/O page.

Configuring the kernel for master/slave

Be sure CONFIG_I2C_PXA_SLAVE is set correctly in your buildroot's linux.config (set to 'n' if your Gumstix will be the master). If this changes, you will need to rebuild the kernel.

Using precompiled modules

The precompiled modules are specific to a version of the kernel.

Copy the appropriate tarball to your gumstix. Let's assume you copied it into /tmp (ramdisk). Do the following to install the precompiled i2c modules: 

cd /
tar xzf /tmp/i2c-modules-2.6.11.tar.gz
cd lib/modules/2.6.11gum
cp modules.symbols modules.symbols.org
cp modules.dep modules.dep.org
cat mod.sym >> modules.symbols
cat mod.dep >> modules.dep

Once you're happy that everything is working you can remove mod.dep, mod.sym, modules.symbols.org and modules.dep.org files.

Building the modules from source

1. Begin by getting a functional Buildroot running.

2. Enter the gumstix-buildroot/target/device/Gumstix/basix-connex (if you are using ether a basix or connex board) directory and edit linux.config (backing it up first...) Add the following lines in the appropriate place (hint: search for "I2C support"): 

# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_PCA_ISA is not set
CONFIG_I2C_PXA=m

or at your own risk use this linux-2.6.11.config or linux-2.6.15.config. You can also setup the i2c stuff through menuconfig: 

cd gumstix-buildroot/build_arm_nofpu/linux-*
make ARCH=arm menuconfig

For the 2.6.11 kernel, under 'I2C Support -->' set 'I2C Support' to <M>. Set 'I2C device interface' to <M>. Under 'I2C Hardware Bus support --->' set 'I2C interface in Intel PXA2x0' to <M>. Exit from menuconfig, saving your changes. The .config file will now contain the appropriate settings. You may want to copy this to gumstix-buildroot/sources/linux.config.

For the 2.6.15 and newer kernels, under 'Device Drivers -->' goto 'I2C Support -->' and set 'I2C support' to <M>. Set 'I2C device interface' to <M>. Goto 'I2C Hardware Bus support' and set 'Intel PXA2XX I2C adapter (EXPERIMENTAL)' to <M>. Exit from menuconfig, saving your changes. The .config file will now contain the appropriate settings. You may want to copy this to gumstix-buildroot/target/device/Gumstix/basix-connex/linux.config.

3. If your buildroot is earlier than revision 767 (your < 767) (note: revision 767 is fairly old - Jan 25, 2006, so this only applies if you're using a really old buildroot), then you'll need to grab the 999-gumstix-i2c-bugfix.patch file and copy it into gumstix-buildroot/sources/kernel-patches . For newer versions of buildroot, the patch is either incorporated, or not required.

4. Remove the old kernel (while you're still in the linux directory). This will trigger the top-level buildroot to actually rebuild linux. 

rm arch/arm/boot/compressed/vmlinux

5. Run "make" at the gumstix-buildroot directory again to build the new kernel.

6. Copy the kernel and modules across or replace the filesystem image.

Starting i2c

Boot the gumstix and then "modprobe i2c-pxa" and "modprobe i2c-dev". Under 2.6.15, you should see some output like this: 

# modprobe i2c-dev
i2c /dev entries driver
# modprobe i2c-pxa
I2C: i2c-0: PXA I2C adapter{CODE}

Under 2.6.11, you should see some output like the following: 

# modprobe i2c-dev
i2c /dev entries driver
# modprobe i2c-pxa
insmod: cannot insert `/lib/modules/2.6.11gum/kernel/drivers/i2c/i2c-core.ko': File exists (-1): File exists
i2c_adapter i2c-0: found device 0x20
i2c_adapter i2c-0: found device 0x7e

The warning about i2c-core.ko is really just saying that it can't load i2c-core for a second time (since it was already loaded when i2c-dev was loaded).

You can automate this step at boot time, by adding the following lines to your /etc/modules file on the gumstix: 

# I2C
i2c-dev
i2c-pxa

The I2C bus should now be active.

When you do the modprobe of i2c-pxa it will report all devices that are detected on the i2c bus (2.6.11 only). The device at entry 0x20 is an LTC1663 D/A that is used to bias the feedback voltage to the core voltage generator (LTC1878) (i.e. don't mess with it). I haven't yet determined whether the 0x7e entry corresponds to a real device or not.

Connecting to the i2c bus

The i2c bus uses 3 signals, SDA, SCL, and ground, all of which are present on the 60 pin hirose connector. Some daughter cards allow the i2c signals to be accessed.

Note that some versions of the Breakout board have pins labeled incorrectly. See the breakout page for more details.

On the back of the waysmall board, amongst the set of 20 pads, the pad closest to the edge of the board and the power connector is the SDA signal, and the one next to it (also by the edge of the board) is the SCL signal. These are both 3.3v signals and don't have any pullup resistors. The waysmall board has a 3.3v regulator on it, just to the left of the power connector. It has LW33 stamped on it. The pin below the 3 (in LW33) is the 3.3v output (see the JTAG connector page which identifies the Vcc pin on the same type of regulator used on the Tweener).

On the robostix board, pin 12 on the UARTS connector is SDA, and pin 16 is SCL. These are both 5v signals and have pullup resistors.

On the Tweener, pin 19 on the hirose connector is SDA, and pin 20 is SCL. The JTAG connector page has a photo of the hirose connector. The TDO pin shown in the photo is pin 22. The via to the left under the T is pin 21, the one under the O is pin 20, and the one under the D is 19. These are all 3.3v signals and don't have any pullup resistors.

Pullup resistors

The I2C bus requires pullup resistors on the SDA and SCL lines. The I2C specification gives some charts for min and max values (see page 39 and 40). For a 5v or 3.3v bus, the minimum pullup resistance should be around 2k ohms. A typical value to use would be 4.7k ohms.

All of the current daughter cards (except the robostix), need to have pullup resistors added, which pullup the SDA and SCL lines to 3.3v levels.

If you use a robostix, the 3.3v pullup resistors are already included. The SDA and SCL lines on the UARTS connector are at 5v levels, and also have pullup resistors on the robostix board.

Various devices connected to the I2C bus

The I2C Max518 example shows how to connect the Maxim MAX518, which is a dual, i2c, digital to analog converter.

The I2C DS1307 example shows how to connect the DS1307, which is an i2c real time clock and nvram chip.

Program for interacting with I2C devices

The i2c program is a simple program which allows reading and writing individual bytes to and from an i2c device. This is sufficient for controlling a large number of i2c devices. The source code for the i2c program can be found in SVN (login "gumstix", password "gumstix"). A precompiled version for 2.6.15 can be found in i2c-2.6.15.tar.gz and for 2.6.11 here.

There are currently two commands which are supported: readbyte (which can be shortened to rb) and writebyte (which can be shortened to wb). For example, to read register 0x2E from a Cypress CY8C9520 you would use the command: 

# i2c 0x21 readbyte 0x2e
0x20

and to write the value 0xAA to GPIO port 0 (which requires a write to register 8) 

# i2c 0x21 writebyte 0x08 0xAA

The readbyte command can use the --count=N option (where N is a number between 1 and 32). For convenience there are 2 and 4 byte version of the readbyte and writebyte commands. There are readbyte2, readbyte4, writebyte2 and writebyte4, which can be shortened to rb2, rb4, wb2, and wb4 respetively.

An example using readbyte to read the RTC from a DS1307: 

# i2c --count=8 0x68 readbyte 0
0x3006000203030600

(which decodes to Mar 30, 2006 00:06:30)

An example using the multibyte write to write 8 bytes to the EEPROM in the DS1307: 

# i2c 0x68 wb 8 0x123456789abcdef0
Retrieved from "http://docwiki.gumstix.org/index.php/I2C_on_the_Gumstix"
Personal tools